Pacific RL360 D5 Hard Tube RGB Water Cooling Kit Pacific RL360 D5 Hard Tube RGB Water Cooling Kit Pacific RL360 D5 Hard Tube RGB Water Cooling Kit Pacific RL360 D5 Hard Tube RGB Water Cooling Kit Pacific RL360 D5 Hard Tube RGB Water Cooling Kit Pacific RL360 D5 Hard Tube RGB Water Cooling Kit Pacific RL360 D5 Hard Tube RGB Water Cooling Kit
Pacific RL360 D5 Hard Tube RGB Water Cooling Kit

Pacific RL360 D5 Hard Tube RGB Water Cooling Kit

Brak w magazynie
P/N
CL-W129-CA12SW-A
419,99 € (included VAT)
LCS combo unit with CPU waterblock, PR22-D5 pump/reservoir, 360mm radiator, Riing 12 RGB fans, PETG tube, C1000 Opaque coolant and other accessories.


Thermaltake Pacific RL360 D5 Hard Tube RGB Water Cooling Kit

As part of its “hardcore” spirit towards the ultimate in custom PC water cooling, Thermaltake has launched the new Pacific RL360 D5 Hard Tube RGB Water Cooling Kit. The kit is composed of one Pacific W1 CPU water block, one Pacific PR22-D5 pump and reservoir combo, one Pacific RL360 radiator, four V-Tubler PETG tubes, six Pacific G1/4 compression fittings (chrome), three Riing 12 LED RGB fans, one C1000 Opaque coolant red and other accessories. Together, these provide exceptional performance, unrivalled reliability, and styling to enthusiasts.

Tt LCS Certified

Tt LCS Certified is a Thermaltake exclusive certification applied only to products that pass the design and hardcore enthusiasts standards that a true LCS chassis should hold to. The Tt LCS certification was created so that we at Thermaltake can indicate to all power users which chassis have been tested to be best compatible with extreme liquid cooling configurations, ensuring you get the best performance from the best features and fitment.

Pacific W1 CPU Water Block

The W1 CPU water block is constructed with a copper base and anti-corrosive nickel plating to provide exceptional heat transfer and cooling performance. Fits all modern CPU sockets.
Learn More

Pacific PR22-D5 Pump/Reservoir Combo

The PR22-D5 includes a 300ml reservoir and D5 pump to provide the perfect combination for proper water cooling circulation and capacity, manufactured from high quality POM and PMMA material.
Learn More


Riing 12 RGB High Static Pressure LED Radiator Fan (3 Fans Pack)

Three patented circular 256 multicolored 120mm RGB radiator fans with high-static pressure design, one smart fan controller included.
Learn More

Pacific RL360 Radiator

With high-density fin design (FPI: 14), the 360mm radiator is optimized to accommodate high airflow and high air pressure with increased capacity and provides superior cooling performance to all components.
Learn More

Pacific G1/4 PETG Tube 16mm (5/8”) OD Compression Fittings (Chrome)

Six durable copper compression fittings allow proper connection to G1/4” ports to properly secure to cooling components.
Learn More


V-Tubler PETG Tube 5/8” (16mm) OD 500mm (4 Pack)

Manufactured from premium PETG, the V-Tubler rigid tubing provides custom PC water cooling configurations with reliability and durability from end to end.
Learn More


C1000 Opaque Coolant Red

Made in Germany, the non-flammable C1000 Opaque Coolant is a ready-to-use cooling solution with at least 3 years shelf life in airtight containers, providing great performance while preventing the entire cooling system – copper, brass, nickel, and aluminum – from corrosion.
Learn More

Remarkable Expansion

The Pacific RL360 D5 Hard Tube RGB Water Cooling Kit provides multiple LCS components for PC enthusiasts to build the ultimate in custom configuration, allowing them to build up aesthetically-superior water cooling systems by incorporating externally-modular upgrades for their chassis.


Cautions

Thermaltake recommends the following steps to be taken before using the Pacific series radiators and water blocks

  • To ensure a clean loop, flush and rinse your radiators and water blocks with distilled water prior to use.
  • Do not use tap water or distilled water as your coolant, it may harm your loop and reduce performance.
  • It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while protecting the entire liquid loop from corrosion.
  • Before storing your water cooling components, please clean, rinse and dry. This will ensure a longer lifespan for your components.

Thermaltake recommends the following steps to be taken after completing your water loop setup

  • It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while preventing the entire cooling system – copper, brass, nickel, aluminum, and steel – from corrosion.
  • Fill the reservoir with coolant and cycle the power on and off several times while the pump pushing the coolant into the loop.
  • DO NOT let the pump run dry, when there is no liquid entering the pump turn off your power immediately
  • Fill the reservoir to the top as it will prevent air from going into the pump
  • If necessary tilt the system slightly from side to side to bleed the air out of the loop.
  • Place some paper towels under fittings and joining points to test for leaks.
  • Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop.

Uwagi

Thermaltake zaleca następujące kroki, które należy podjąć przed użyciem chłodnic i bloków wodnych z serii Pacific:

  • Aby zapewnić czystą pętlę, przed użyciem przepłucz chłodnice i bloki wodne wodą destylowaną.
  • Nie używaj wody z kranu ani wody destylowanej jako chłodziwa, może to uszkodzić pętlę i zmniejszyć wydajność.
  • Zdecydowanie zaleca się stosowanie sprawdzonego na rynku wstępnie zmieszanego płynu chłodzącego, takiego jak Thermaltake Coolant 1000. Zapewnia on doskonałą wydajność, jednocześnie chroniąc cały obieg cieczy przed korozją.
  • Przed przechowywaniem elementów do chłodzenia wodą należy je wyczyścić, wypłukać i wysuszyć. Zapewni to dłuższą żywotność komponentów.

Thermaltake zaleca następujące kroki, które należy wykonać po zakończeniu konfiguracji pętli wodnej:

  • Zdecydowanie zaleca się stosowanie sprawdzonego na rynku wstępnie zmieszanego płynu chłodzącego, takiego jak Thermaltake Coolant 1000. Zapewnia on doskonałą wydajność, jednocześnie zapobiegając korozji całego układu chłodzenia – miedzi, mosiądzu, niklu, aluminium i stali.
  • Napełnij zbiornik płynem chłodzącym i kilkakrotnie włączaj i wyłączaj zasilanie, podczas gdy pompa wpycha płyn chłodzący do pętli.
  • NIE pozwól, aby pompa pracowała na sucho, jeśli do pompy nie dostanie się płyn, natychmiast wyłącz zasilanie.
  • Napełnij zbiornik do góry, ponieważ zapobiegnie to przedostawaniu się powietrza do pompy
  • W razie potrzeby lekko przechylić system na boki, aby wypuścić powietrze z pętli.
  • Umieść kilka ręczników papierowych pod łącznikami i punktami łączenia, aby sprawdzić, czy nie ma wycieków.
  • Uruchom pętlę z otwartym portem napełniania na około 24 godziny, aby całkowicie usunąć powietrze z pętli.
  • Przed rozpoczęciem należy dokładnie przepłukać system, aby zapobiec przywieraniu chłodziwa lub niepożądanych cząstek do rur, chłodnic i innych elementów chłodzących.
  • Płyn chłodzący może z czasem wyblaknąć.
Więcej informacji
P/N CL-W129-CA12SW-A
Waga 5.5 kg
ZGODNOŚĆ Intel LGA 2011/1366/1155/1156/1151/1150/775
AMD FM2/FM1/AM3+/AM3/AM2+/AM2
Components Dimensions Pump&Reserooir: 289.4 (H) x 84 (W) x 97.5(L)
Radiator : 64 (H) x 129 (W) x 402.5 (L)
Tube Dimensions OD : 16mm , ID : 12mm , L : 500mm
Kit Contents CPU Water Block
- Pacific W1 CPU Water Block x1 Pump/Reservoir
- Pacific PR22-D5 Pump/Reservoir Combo x1 Radiator
- Pacific RL360 Radiator x1 64 (H) x 129 (W) x 402.5 (L) x1 Fittings
- Pacific G1/4 PETG Tube 16mm OD Compression
- Chrome x6 Fan - Riing 12 LED Radiator Fan 256 Color 3 Pack Tube
- V-Tubler PETG Tube 16mm(5/8") OD 500mm 4Pack x1 Coolant
- C1000 Red Opaque Coolant 1000ml x1 Accessory
- Intel and AMD Universal Backplated & Mounting Kit
- 24pin ATX Bridge Tool x1
- Thermaltake Thermal Grease x1

User Manual

  • Nazwa pliku
  • Opis
  • Rozmiar
  • Version
  • Release Date
  • Manual
  • Multi-language
  • 18.3 MB
  • 2016-05-17